Advanced Energy Meters and Demand Control Meters


Invendis Advanced energy Meters enables two way-communication network to control centre equipment and all the applications that enable the gathering and transfer of energy usage information in near real-time. Advanced energy meter enables remote meter reading for error free data, network problem identification, load profiling, energy audit and partial load curtailment in place of load shedding.

Demand Control meters are special advanced meters that enable the user to program the threshold values of maximum energy demand and initiate actions i.e. alarm or cut off load when maximum demand / forecast demand / present demand crosses the threshold values. This helps the user to ensure that demand does not exceed the sanctioned limit and avoid paying huge penalties.

Our meters capture all parameters and transmit it V, A, F, kW, KVA, kVAr, kWh, kVAh, kVArh, PF, Runhr, Onhr, Intr, Phase angle, THD, Events, Neutral current, Max Demand (with RTC) with 3 relay outputs. The parameters can be integrated with GSM module for data transmission over GPRS.

Available across various Communication Interfaces


ET - 5002


Advanced Meters

All basic Parameters along with Demand capture & Neutral current

Used for enhancing energy efficiency requirement like Analysis and Control

Ideal for motor drives, buildings with load / demand control requirements, data centers etc.

Relay to control additional load than the set demand.

It supports dual source feature

Communication over GPRS and WIFI

Usage :

This meter is mainly used in industrial and commercial segment where advanced parameters and demand capturing becomes prime factor.

Commercial buildings to capture peak load, comparison with sanctioned load etc.

The meter also aids in understanding the imbalance in the system through Neutral current which helps clients to upkeep the efficiency of the system.

Technical Specifications

Configuration : 1/3 Phase, 3 Element; 3 / 4 Wire (Note Order code)

Input V Nominal : 415 V LT or 110 V through PT (line to line) Computation : True RMS for all Power & Energy Parameters

Accuracy :
-- ± (0.5% of FS + 0.5% of Rdg + 1 digit)
-- ± 0.2% for Frequency
-- ± 1.0% of FS for Current

Isolation : 2000 V AC for one minute

Safety : Measurement Category III, Pollution Degree 2 as per EN61010-1 First Edition Frequency : 0.1 Hz

Power : autoscaling depending on input

Power Factor : 0.01

Energy : 1 kWH upto 866 kW

10 kWH above 866 kW


ET - 5011


Advanced Meters

All basic Parameters along with Demand capture & Neutral current

Used for enhancing energy efficiency requirement like Analysis and Control

Ideal for motor drives, buildings with load / demand control requirements, data centers etc.

Relay to control additional load than the set demand.

It supports dual source feature Communication over RS485, BACnet & Zigbee

Usage :

This meter is mainly used in industrial and commercial segment where advanced parameters and demand capturing becomes prime factor.

Commercial buildings to capture peak load, comparison with sanctioned load etc.

The meter also aids in understanding the imbalance in the system through Neutral current which helps clients to upkeep the efficiency of the system.

Technical Specifications

Configuration : 1/3 Phase, 3 Element; 3 / 4 Wire (Note Order code)

Input V Nominal : 415 V LT or 110 V through PT (line to line)

Computation : True RMS for all Power & Energy Parameters

Accuracy :
-- ± (0.5% of FS + 0.5% of Rdg + 1 digit)
-- ± 0.2% for Frequency
-- ± 1.0% of FS for Current

Isolation : 2000 V AC for one minute

Safety : Measurement Category III, Pollution Degree 2 as per EN61010-1 First Edition

Frequency : 0.1 Hz

Power : autoscaling depending on input

Power Factor : 0.01

Energy : 1 kWH upto 866 kW

10 kWH above 866 kW


ET - 6001


Demand Control Meter

Captures peak demands

controls non-critical loads to balance and the consumption.

Captures all basic parameters and the demand

The pre-built logic enables the load trip function when the load / demand increases beyond the set threshold.

Ideal for applications in building electrical distribution.

GSM module for data transmission over GPRS

Usage :

This meter is mainly used in industrial and commercial segment where advanced parameters and demand capturing becomes prime factor.

Commercial buildings to capture peak load, comparison with sanctioned load etc.

The meter also aids in understanding the imbalance in the system through Neutral current which helps clients to upkeep the efficiency of the system.

Additionally with control feature, the meter ensures that the system shall not exceed the sanctioned load and helps customer to minimise the penalties.

Technical Specifications

Configuration : 1/3 Phase, 3 Element; 3 / 4 Wire (Note Order code)

Input V Nominal : 415 V LT or 110 V through PT (line to line)

Computation : True RMS for all Power & Energy Parameters

Accuracy :
-- ± (0.5% of FS + 0.5% of Rdg + 1 digit)
-- ± 0.2% for Frequency
-- ± 1.0% of FS for Current

Isolation : 2000 V AC for one minute

Safety : Measurement Category III, Pollution Degree 2 as per EN61010-1 First Edition

Frequency : 0.1 Hz

Power : autoscaling depending on input

Power Factor : 0.01

Energy : 1 kWH upto 866 kW

10 kWH above 866 kW

Ranges